Furibee F36 frame mod for FPV camera mounting 

I have recently purchased a FPV AIO micro camera from Gearbest to hook it to my Furibee F36.

I have tried various mounting options and the mount camera above the mainboard seemed to be the best option. However this gave the some degree of uncertainty to the left-right movements due to the lifted center of gravity. I have decided to modify the frame to be able to place the camera as low as is possible.

After some investigation moving the main PCB right above the battery seemed to be a viable modification. I have estimated to lower the camera mounting position with 5 mm with this mod.

There is a saying in Hungary: if you have a hammer you will threat everything as a nail. This saying also applies to me, but my hammer is my CNC mill. So I have hooked my frame to the mill and removed the necessary parts with it:


I. Remove the battery closing end.
(We are going to install the battery from this end and the battery connector will secure it in the forward-backward direction.)



II. Remove the PCB securing standoff



III. Rasp two V shapes to the PCB to be able to fit properly from the frame's side holders.



IV. After installing the mainboard in the new place drill a 1mm diameter hole to the screws new location, and then install the screws.




V. Cut a bit from the rear screw length because it will cut through the frames plastic and it could hurt the battery.



[ hozzászólás ] ( 264 megtekintés ) [ 0 trackbackek ] permalink ( 3.1 / 306 )
STM8 SWIM Tag Connect pinout 


[ hozzászólás ] ( 4 megtekintés ) [ 0 trackbackek ] permalink ( 3 / 277 )
John Deere RE219053 javítás 

Szembekerültem egy ilyen monitorral aminek az egyik gombja bedöglött.
A gombok fóliamátrix kialakításúak, ezért az egyik legtöbbet használt gomb bemondta az unalmast, folyamatosan kontaktot adott.

Kapott hát egy szép kis bohócorrot a helyére:



Szépen bedrótoztam a helyére:



Gomb csati lábkiosztása:


[ hozzászólás ] ( 7 megtekintés ) [ 0 trackbackek ] permalink ( 3 / 241 )
Ebay review: 614 Micro Motor DC 3.7V 

I have came across many similar small motors on ebay:


By looking at their dimensions I couldn't resist to buy a few one to try out how they perform in my Furibee F36.

Here are the plain results running from 4.2V bench supply:
No load current: 60 mA
Consumed current while driving the Furibee's 32mm ducted fan: 570 mA

As seen from the currents above (Furibee's motors consuming ~1A with FAN) these motors are not as powerful as the Furibee's.

The thing can fly, but not as agile as with the original motors.
[ hozzászólás ] ( 5 megtekintés ) [ 0 trackbackek ] permalink ( 3.1 / 176 )
UDEV rule for setting the baudrate and bringing up socketcan interfaces 


SUBSYSTEM=="net", ACTION=="add", KERNEL=="can*", RUN+="/etc/udev/rules.d/setup_can_interfaces.sh"


And the setup_can_interfaces.sh:


#!/bin/bash

/sbin/ip link set $INTERFACE type can bitrate 1000000
/sbin/ifconfig $INTERFACE txqueuelen 1000
/sbin/ifconfig $INTERFACE up



Do not forget to add executable rights and then reload the udev rules:
udevadm control --reload-rules && udevadm trigger

[ hozzászólás ] ( 3 megtekintés ) [ 0 trackbackek ] permalink ( 3 / 168 )

<< <Előző | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | Következő> >>

 
számláló